RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: olnico
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Forum: RC Jets
02-09-2021, 09:52 AM
Replies: 746
Views: 177,806
Posted By olnico

https://cimg0.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg0.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/1013x675/montage_69d4b256b21af12c17ecb80755656391e5c26a8b.jpg
The last picture shows a full up elevator and a flat stabilizer. Doesn't it?...
Forum: RC Jets
02-09-2021, 09:47 AM
Replies: 746
Views: 177,806
Posted By olnico

That sounds very strange to me. On most...

That sounds very strange to me.
On most aircraft, the all moving tailplane is a trimmer and the elevators are the primary pitch control unit.
Given the size of the elevators, I would strongly...
Forum: RC Jets
02-07-2021, 09:34 PM
Replies: 746
Views: 177,806
Posted By olnico

Can you send me the log file?

Can you send me the log file?
Forum: RC Jets
02-07-2021, 07:55 PM
Replies: 746
Views: 177,806
Posted By olnico

Hi Paul. Sorry for the loss. I hope that...

Hi Paul.
Sorry for the loss.

I hope that you had a good telemetry system that will get you all the data you need to secure the next prototype.
At this stage in the design cycle, you are in good...
Forum: RC Jets
02-01-2021, 10:37 AM
Replies: 746
Views: 177,806
Posted By olnico

Best of luck for the maiden!

Best of luck for the maiden!
Forum: RC Jets
01-19-2021, 07:36 AM
Replies: 746
Views: 177,806
Posted By olnico

Here you go Paul. You found the problem.

Here you go Paul. You found the problem.
Forum: RC Jets
01-13-2021, 06:38 PM
Replies: 746
Views: 177,806
Posted By olnico

If you build in a garage or close to it, you...

If you build in a garage or close to it, you could also get contamination from exhaust gas.
Forum: RC Jets
01-13-2021, 01:28 AM
Replies: 746
Views: 177,806
Posted By olnico

Most peel plies are 100% pure nylon 6-6. Like...

Most peel plies are 100% pure nylon 6-6.
Like the one sold on R&G shop and many other shops.

However, if the peel ply is coated, it should be described as " nylon release peel ply" or " polyester...
Forum: RC Jets
01-04-2019, 11:03 AM
Replies: 746
Views: 177,806
Posted By olnico

I doubt. It looks like the release angles in that...

I doubt. It looks like the release angles in that direction are too shallow. The mold is funneled by the engine pod.
Forum: RC Jets
11-26-2018, 10:15 AM
Replies: 746
Views: 177,806
Posted By olnico

With a very carefully designed bypass system,...

With a very carefully designed bypass system, this will work with the 100 XBL.
I have this exact pipe working on the Crusader. With a 4 mm air cooling gap.
Most of our larger engine pipes use a 5...
Forum: RC Jets
11-26-2018, 10:12 AM
Replies: 746
Views: 177,806
Posted By olnico

Your split is too far away from the engine...

Your split is too far away from the engine nozzle.
If you make the Y pipe with a shorter initial tube and Inconel splltter, you might be able to reduce the Y angle below 40 degrees.
As you get...
Forum: RC Jets
11-23-2018, 09:54 PM
Replies: 746
Views: 177,806
Posted By olnico

Yes, you're gonna have to watch the airframe...

Yes, you're gonna have to watch the airframe weight.
You might want to consider using airex/ carbon fiber internals instead of lightply. Except for the landing gear support structure.
You should...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.