RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: randykrul
Showing results 1 to 12 of 12
Search took 0.13 seconds.
Forum: RC Jets
10-25-2005, 01:54 PM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Here is my speed brake. I got this idea where Bob Violet did this on his Bob Cat. I have a high torque metal gear servo.
Randy
Forum: RC Jets
10-24-2005, 04:42 PM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Joe
I also have a spped brake on the bottom. It is 2 1/4 X 6, made from carbon fibre plate. It would be easy to put on a different size as the plate just rests against the bottom of the fuse. We...
Forum: RC Jets
10-24-2005, 02:17 PM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Yes I thought about the chrome, but the bottom is very dark with orange tips as well, we will see. The wing-lets were just something added for fun, they extend below the wing for tip skids as well.
...
Forum: RC Jets
10-24-2005, 01:28 PM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Here are some pictures of my Enforcer. It came out at 12lbs. dry, powered by a JDE 54 air start. It has Spring Air Retracts, Eurokit Struts, Intairco wheels and brakes, full cycle gear doors (...
Forum: RC Jets
09-29-2005, 03:36 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Thanks Joe
If I go with a 17 inch CG, from trailing edge ( not including the tail surfaces ) , then that makes my main tank about 2/3 in front of the CG and 1/3 behind. I might be able to move the...
Forum: RC Jets
09-28-2005, 03:41 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

I am finally finishing my turbine Enforcer. I measured the CG on the plans and come up with 16 inches from the very end of the trailing edge. I noticed some of you have suggested moving the CG...
Forum: RC Jets
06-17-2005, 04:52 PM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Hi Joe
I hoping to get back to finishing the enforcer. It is ready to cover and final radio install and cg balance. I'll send more photos when I get more finished.
Randy
Forum: RC Jets
04-21-2005, 03:49 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Joe
You were very helpful. I did make thicker fins, they are laminated 3/16!QUOT! balsa center with 3/32!QUOT! balsa sheeted in different directions on both sides. The fins will be glued in...
Forum: RC Jets
04-19-2005, 03:23 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Here are 2 more pictures.
Forum: RC Jets
04-19-2005, 03:21 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

Since this post started, I ordered an enforcer and have it well on its way. I have a JDE 54 turbine, springair retracts, Eurokit struts, Intairco wheels and brakes. I have operating gear doors. I...
Forum: RC Jets
01-17-2005, 12:36 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

To Cars II

Sorry I did not see your post until tonight, I was out of town. I fly my turbines at the EBRC field in Livermore. I usually go late Sunday afternoons when most of the other members...
Forum: RC Jets
01-13-2005, 05:08 AM
Replies: 142
Views: 32,729
Posted By randykrul

RE: Turbine Enforcer

To Chet

I have an Enforcer on order and want to modify it like yours. I will be using a JDE 54 production turbine engine ( 15lbs thrust )
Could you supply more info & pix on the canard. Is it...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.